Seiko V-64S Guia do Utilizador Página 170
- Página / 233
- Índice
- RESOLUÇÃO DE PROBLEMAS
- MARCADORES
Avaliado. / 5. Com base em avaliações de clientes
4-22
7
Pull out the Wiper blade while lifting
upward.
8
Pinch the rubber portion of a new
Wiper blade with tweezers and insert
straightly the Wiper blade from the top.
Finally, install it so that the plastic projection
is hooked to the hole of rubber portion.
Note
- The front and back of the wiper are the same.
- As the upper portion of Wiper blade touches directly the Print head, do not
touch it by hand or pinch it with tweezers when handling.
Upper portion of Wiper blade
9
Close the Cap cover and the Front cover.
10
Select [
*
YES] and press key to nish.
Note
- The printer automatically tracks the time the Wiper blade is used and displays
the message prompting to replace the Wiper blade. If a new Wiper blade is
installed and [*YES] is set, the value of accumulator is reset.
#R EPLACE FIN IS HED
*
NO
#R EPLACE FIN IS HED
*
YES
IP-5610取説_E.indb 22 09.4.3 3:15:12 PM
- User's Guide 1
- Introduction 5
- Basic conguration item 7
- Supplied Accessories 7
- Safety precautions 9
- Handling precautions 12
- Consumables 13
- Printer warranty 13
- Notations 14
- Starting out 16
- When you want to . . 18
- Replacement/Trouble 20
- TABLE OF CONTENTS 21
- Basic operation 22
- Menu of Operation panel 23
- Overview 25
- Operating conditions 26
- Environmental conditions 27
- Before use (Basic knowledge) 29
- Head up down mechanism 30
- Print heads 30
- Carriage 30
- Rear heater 31
- Print heater 31
- Front heater 31
- Operation Panel 32
- Exhaust attachment 33
- 2 inch ange 33
- 3 inch ange 33
- WARNING 36
- CAUTION 37
- Waste ink bottle 38
- Daily maintenance kit 39
- Cap cleaning liquid 39
- Wiper cleaning liquid set 40
- Cap cleaning stick 40
- Cap cleaning roller set 40
- How to read LCD 42
- The ONLINE LED blinks 43
- The ONLINE LED lights 43
- Connection to a computer 48
- Power ON / OFF procedure 49
- Power-on procedure 50
- Power-o procedure 52
- Media replacement 53
- Print side 54
- Roll media removal procedure 59
- NO MEDI A LOADE D 60
- LOA D M EDI A 60
- Cut media removal procedure 61
- Inner take-up 67
- Winding OFF 67
- Outer take-up 67
- Attachment 68
- 3 inch adapter 68
- How to use the blower unit 69
- Handling the media 70
- When pushing this portion 71
- How to switch the pressure 72
- How to use the lifter 73
- Cut the media 74
- Feeding the media [Feed] 75
- Rewind the media [Back Feed] 76
- Margin Set the origin 77
- [ ] Label 77
- ¢ Heater control menu display 79
- Print heater set temperature 81
- Rear heater set temperature 81
- Front heater set temperature 81
- Standby set temperature 81
- Ambient temperature 81
- Change the Print head height 82
- Ink cartridge replacement 84
- Waste ink bottle replacement 86
- Select “BOTTLE EMPTY? 87
- YES” and press key 87
- Menu layer structure 91
- Menu tree 92
- Select [RENAME MEDIA MENU] 103
- ( + key) 104
- Character code group 104
- INK MENU 105
- MEDIA MENU 106
- (In case of display in mm) 107
- (In case of display in inch) 107
- MEDIA REG MENU 108
- ¢ Preset media initial value 110
- (1) SELECT MEDIA 112
- (2) RENAME MEDIA 112
- (3) MEDIA ADV VALUE 112
- (4) DRY TIME VALUE 113
- (5) PRINT MODE 113
- (6) PRINT DIRECTION 114
- (7) FLATTENING 115
- (8) EDGE GUARD 116
- (9) MEDIA ADV MODE 116
- (10) Take-up (TUR) MODE 116
- (11) LEADING EDGE 117
- (12) VACUUM LEVEL 117
- (13) FRONT HEATER T 118
- (14) PRINT HEATER T 118
- (15) REAR HEATER T 118
- (16) COLOR STRIPE 119
- (17) IMAGE GRADIENT 119
- (18) PH HEIGHT VAL 119
- (19) BIDIR ADJ1 L 120
- (20) BIDIR ADJ1 R 120
- (21) BIDIR ADJ2 L 120
- (22) BIDIR ADJ2 R 121
- (23) BIDIR ADJ3 L 121
- (24) BIDIR ADJ3 R 121
- Correct with the 122
- Cleaning 122
- Half way on the path 123
- (30) HEATER PREF 124
- (31) PH REST PERIOD 124
- (32) PH REST TIME 124
- (33) PH TEMP REST 125
- (34) SET REMAINING MEDIA 125
- (35) DELETE MEDIA 125
- PASTE MEDIA 127
- M.ADV MENU 128
- (3) BACK ADJUST PRINT 130
- (4) BACK ADJUST VAL 130
- REWIND MENU 131
- PH.REC MENU 132
- FORM FEED MENU 133
- PH.MAIN MENU 134
- (3) REPLACE WIPER BLADE 135
- (4) REPLACE WIPE LIQUID 135
- (5) REPLACE WIPER SPONGE 135
- (6) Fill Cap 135
- (7) PH HEIGHT ADJ 136
- (8) RESEAT PRINT HEAD 136
- (9) PH WARM 136
- PRINTER MENU 137
- ADJUST MENU 138
- (2) PH TO PH VAL 139
- (3) PH R&L ADJ VAL 139
- (4) BIDIR ADJ1 L 139
- (5) BIDIR ADJ1 R 139
- (6) BIDIR ADJ2 L 140
- (7) BIDIR ADJ2 R 140
- (8) BIDIR ADJ3 L 140
- (9) BIDIR ADJ3 R 140
- (10) NOZZLE POS VAL 141
- (11) LS ADJ TOP VAL 141
- (12) LS ADJ SIDE VAL 141
- SETUP MENU 142
- (3) Length Unit 143
- (4) Temperature Unit 143
- (5) Head warming-up 143
- (6) BEEP 144
- (7) BOOT Version 144
- (8) F/W version 144
- (9) LEE version 144
- (10) LEC version 145
- (11) USB address 145
- (12) USB speed 145
- (13) Initial Setting 145
- (14) Update 146
- (15) Download 146
- HEATER MENU 147
- Maintenance and 149
- Adjustment / Replacement 149
- Periodic maintenance 150
- P.4-21 [ 152
- Wiper blade replacement 152
- P.3-56 [(6) BEEP]) 154
- P.4-19 [Print head cleaning]) 155
- Media advancing direction 157
- Head wash]) 158
- P.4-11 [(1) 158
- #I NK SYST EM OPT 160
- >C HAR GE IN K S YS 160
- Seiko I Infotech 161
- Head guard 166
- Cleaning swab 166
- Soft clothSoft cloth 166
- Print head cleaning 167
- Wiper sponge replacement 173
- #R EPLACE FIN IS HED 174
- Media advance value setting 176
- Change during online printing 180
- Head position adjustment 181
- Media feeding direction 185
- -32 -31 -30 -29 -28 -1 187
- 0 +1 +2 +3 +4 +31 187
- Blank area 192
- Press key 194
- Initial adjustment 195
- Adjustment during operation 195
- Groove of Tension bar 196
- Horizontal line of 196
- Adjustment during operation 197
- Troubleshooting 199
- When Encountering a Problem 200
- No printing 201
- Slow printing 203
- How to clear media jams 204
- Service call error 205
- (system error) 205
- (Ink cartridge) 206
- Operator call error 206
- (Waste ink bottle) 207
- (Media jam) 207
- (Print head) 209
- CLOS E COVE R 210
- EN V. T EMP. ERR O R 210
- CH ANGE ENV TEMP 210
- • The ink LED blinks. : 212
- How to get good image quality 213
- Black streaking on the print 215
- Bleeding on the print 217
- Skew example Sag example 219
- Abnormal sound 223
- Use of generic consumables 225
- Safety issues 226
- Cleaning liquid 229
- Appendix 231
- Basic specications 232
- Options / Consumables 233
Manuais e produtos relacionados com Digitalizar e Imprimir Seiko V-64S
Digitalizar e Imprimir Seiko 201 Especificações
(52 páginas)
(52 páginas)
Digitalizar e Imprimir Seiko TM-T90 Especificações
(214 páginas)
(214 páginas)
Digitalizar e Imprimir Seiko TM-T90 Manual
(22 páginas)
(22 páginas)
© 2020, manymanuals-pt.com. Todos os direitos reservados. | 0.048 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comentários a estes Manuais