Seiko BX-900 Especificações

RP-E10 SERIES THERMAL PRINTER TECHNICAL REFERENCE U00127424203

1-1 CHAPTER 1 TERMS USED IN THIS MANUAL This chapter describes the terms used in this manual. • INPUT BUFFER AND LINE BUFFER When the RP-E10 (here

6-35 DC2 'Q' Optional Font Area Release Code 12H 51H Function Releases the memory area for the registered optional fonts. The registered

6-36 6.5.4 Print Position ESC 'L' Page Mode Select Code 1BH 4CH Function Switches the mode from the standard mode to the page mode. Note

6-37 ESC 'S' Standard Mode Select Code 1BH 53H Function Switches the printer unit from the page mode to the standard mode. Notes This c

6-38 When starting point is "upper right" or "lower left" through ESC 'T' (characters mapped in paper feed direction)

6-39 Notes The horizontal tab position is set as [n × character width] from the left margin or the beginning of the line. Character width here means

6-40 Function Sets the left margin set with nl and nh. The left margin is [(nh × 256+nl) × basic calculation pitch] inches. Notes This command is ef

6-41 GS 'W' nl nh Print Area Width Set Code 1DH 57H nl nh Definition Range 0≤nl≤255 0≤nh≤255 Default Printable area Function Se

6-42 ESC 'T' n Character Print Direction Specify in Page Mode Code 1BH 54H n Definition Range 0≤n≤3, 48≤n≤51 Default When the MS13-2 (

6-43 ESC 'W' xL xH yL yH dxL dxH dyL dyH Print Area Set in Page Mode Code 1BH 57H xL xH yL yH dxL dxH dyL dyH Definition Range 0≤xL, xH

6-44 When the page mode is selected, the ruled line data specified by the ruled line command (DC3) is affected by the print area specified by this c

1-2 • Line Spacing Line spacing is the space between the lines of printed characters (See Figure 1-2). ABC ABC Line Spacing Figure 1-2 Line Spa

6-45 Notes Specified values that fall outside the print area are ignored. In relation to the character direction, to specify a right position of the

6-46 Character data: Bottom edge of character Bit image: Bottom edge of bit image Downloaded bit image: Bottom edge of dow

6-47 6.5.5 Image ESC '*' m nl nh [d]k Bit Image Mode Print Code 1BH 2AH m nl nh [d]k Definition Range m=0, 1, 32, 33 0≤nl≤255, 0≤

6-48 GS '*' x y [d]k Downloaded Bit Image Registration Code 1DH 2AH x y [d]k Definition Range 1≤x≤255, 1≤y≤255, 0≤d≤255, 8≤k≤65524

6-49 (1) GS '/' m Downloaded Bit Image Print (2) GS '/' m n Downloaded Bit Image Selection Code (1) 1DH 2FH m (2) 1DH 2FH m n

6-50 When this command is received with m in the range 0≤m≤3 or 48≤m≤51, printing starts immediately. When m is in the range 4≤m≤7 or 52≤m≤55, the s

6-51 When executing this command, reduced printing speed due to communication speed may cause poor print quality or abnormal noise. Therefore, this

6-52 DC2 '=' n Image LSB/MSB Selection Code 12H 3DH n Definition Range 0≤n≤255 Default n=1 Function When the row scan method is selec

6-53 GS '(' 'L' pL pH '0' fn NV Graphics Memory Capacity Response Code 1DH 28H 4CH pL pH 30H fn Definition Range pL

6-54 GS '(' 'L' pL pH '0' fn NV Graphics Memory Remaining Capacity Response Code 1DH 28H 4CH pL pH 30H fn Definition

1-3 • Notation in the Technical Reference Hexadecimal Hexadecimal is shown as follows; Example: 0AH (a hexadecimal unit 'H' is added beh

6-55 GS '(' 'L' pL pH '0' fn 'C' 'L' 'R' NV Graphics Data Batch Deletion Code 1DH 28H 4

6-56 GS '(' 'L' pL pH '0' fn kc1 kc2 x y Specified NV Graphics Data Print Code 1DH 28H 4CH pL pH 30H fn kc1 kc2 x y D

6-57 GS '(' 'L' pL pH '0' fn kc1 kc2 x y z Specified NV Graphics Data Select Code 1DH 28H 4CH pL pH 30H fn kc1 kc2 x

6-58 Function Defines the NV graphics data in accordance with key code kc1 and kc2. Defining several NV graphics data which have different key code i

6-59 (1) GS '(' 'L' pL pH '0' fn '0' bx by '1' xL xH yL yH [d]k (2) GS '8' 'L'

6-60 MSBLSB(yH × 256+yL) dotsd1 d2dk(xH × 256+xL) dotsd (int(X+7)/8)7 6 5 4 3 2 1 0 Related Commands GS '(' 'L' GS '(&apo

6-61 6.5.6 Macro GS ':' Macro Definition Start/Stop Code 1DH 3AH Function Starts and stops macro definition. Macro is not registered at

6-62 GS '^' r t m Macro Execution Code 1DH 5EH r t m Definition Range 0≤r≤255, 0≤t≤255 m=0, 1 Function Executes macro definition

6-63 6.5.7 Barcode GS 'H' n HRI Character Print Position Selection Code 1DH 48H n Definition Range 0≤n≤3, 48≤n≤51 Default n=0 Functio

6-64 GS 'h' n Barcode Height Set Code 1DH 68H n Definition Range 1≤n≤255 Default n=162 Function Sets the barcode height to n dots. Re

2-1 CHAPTER 2 SPECIFICATIONS 2.1 PRINTER SPECIFICATIONS Table 2-1 Printer Specifications (1/2) Specifications Paper Width: 80mm*1 Paper Width: 58

6-65 GS 'j' n Barcode Print Direction Specify Code 1DH 6AH n Definition Range 0≤n≤3 Default n=0 Function Specifies the barcode print

6-66 DC2 ':' n Barcode N:W Ratio Set Code 12H 3AH n Definition Range 0≤n≤2 Default n=1 Function Changes the barcode N:W ratio (Narrow

6-67 (1) GS 'k' m [d]k NUL (2) GS 'k' m n [d]n Barcode Print Code 1DH 6BH m [d]k 00H (0≤m≤6) 1DH 6BH m n [d]n (65≤m≤73) 1DH 6

6-68 Notes The command configuration, code, domain, and some notes differ depending on the value of m. When m=0 to 6 and m=65 to 71, or m=22 and m=87

6-69 When the barcode width exceeds the print area in page mode, barcode printing is not performed, and the mapping start position of the data shift

6-70 [Barcode print in the page mode] BaselineCHRI characterBarcodeHRI character UPC A: Input 11 characters using numbers between '0'

6-71 CODE93 Code Set ValueDataDataDataValueValue CODE128 Code Set Related Commands GS 'H', GS 'f', GS 'h', GS &ap

6-72 6.5.8 Two-dimensional Barcode GS 'n' n Nominal Fine Element Width Code 1DH 6EH n Definition Range 2≤n≤4 (dot count) Function Sets

6-73 DC2 ';' n QR Code, Data Matrix Module Size Set Code 12h 3BH n Definition Range 2≤n≤11 Default n=6 Function Specifies a module si

6-74 Notes When specifying any value out of the defined range, this command is ignored, and the subsequent data is processed as the normal data. When

2-2 (2/2) Specifications Paper Width: 80mm*1 Paper Width: 58mm*1 Font type 1-byte character Codepage 437: USA, Standard Europe Katakana character s

6-75 GS 'p' 2 ecc row col nl nh [d]k Data Matrix Print Code 1DH 70H 02H ecc row col nl nh [d]k Definition Range ecc=00H 0=row, 8≤

6-76 GS 'p' 3 mode ・・・ n [d]k Maxi Code Print Code 1DH 70H 03H 02H sc cc pc n [d]k (mode2) 1DH 70H 03H 03H sc cc pc n [d]k (mode3) 1D

6-77 6.5.9 Kanji FS '&' Kanji Mode Specify Code 1CH 26H Function Specifies the kanji mode. Notes When the kanji code system is the

6-78 FS '!' n Kanji Print Mode Specify Code 1CH 21H n Definition Range 0≤n≤255 Default n=0 Function Specifies the kanji print mode. B

6-79 FS '-' n Kanji Underline Specify Code 1CH 2DH n Definition Range 0≤n≤2, 48≤n≤50 Default n=0 Function Specifies and cancels kanji

6-80 The kanji code valid in the Shift JIS code system is as follows. 1st byte: 81H to 9FH, E0H to EFH, and FAH to FCH 2nd byte: 40H to 7EH and 80

6-81 FS 'W' n Kanji Double Height and Double Width Specify/Cancel Code 1CH 57H n Definition Range 0≤n≤255 Default n=0 Function Specif

6-82 FS 'I' a b c 2-byte Font ID Send Code 1CH 49H a b c Definition Range a=0 b=0 0≤c≤5 Function Send specified c inform

6-83 FS '2' c1 c2 [d]k User-Defined Character Registration Code 1CH 32H c1 c2 [d]k Definition Range The domain differs depending on the

6-84 DC2 'G' n User-Defined Character Area Operation Code 12H 47H n Definition Range 0≤n≤255 Function Releases and allocates user-defi

2-3 2.1.1 Applicable Standards • This printer complies with laws and regulations of information equipment in the countries listed below when it is u

6-85 6.5.10 Auxiliary Functions ESC '=' n Peripheral Equipment Selection Code 1BH 3DH n Definition Range 0≤n≤255 Default n=1 Function

6-86 DC2 '@' Hardware Reset Code 12H 40H Function Performs hardware reset. Notes Performs the same operation as during power on. GS FF

6-87 Notes This command is effective only when marked paper is selected. This command is executed when is input immediately after the marked paper fo

6-88 GS 'C' '0' n m Counter Print Mode Set Code 1DH 43H 30H n m Definition Range 0≤n≤5 0≤m≤2, 48≤m≤50 Default n=0, m=0

6-89 Notes When [aH × 256+aL<bH<256+bL and n≠0 and r≠0], the count-up mode is set. When [aH × 256+aL>bH>256+bL and n≠0 and r≠0], the cou

6-90 GS 'I' n Printer ID Send Code 1DH 49H n Definition Range 1≤n≤3, 49≤n≤51, 65≤n≤67, 97≤n≤100 Function Sends the specified printer I

6-91 (1) GS 'V' m (2) GS 'V' m n Paper Cut Code (1) 1DH 56H m (2) 1DH 56H m n Definition Range (1) m=0, 1, 48, 49 (

6-92 Notes Only the LSB is valid for n. This command is not effective when the page mode is selected. This command is executed during the line. Wh

6-93 DLE DC4 fn m t Specification Pulse Realtime Output Code 10H 14H fn m t Definition Range fn=l 0≤m≤255, 1≤t≤8 Function Drives the drawe

6-94 GS 'g' '0' m nl nh Maintenance Counter Initialization Code 1DH 67H 30H m nl nh Definition Range m=0 (nh × 256+nl)=

2-4 2.1.2 Precautions For Use • When the two-dimensional barcode and ladder barcode is printed at high speed, it may reduce the bar code's read

6-95 GS 'g' '2' m nl nh Maintenance Counter Transmission Code 1DH 67H 32H m nl nh Definition Range m=0 nh × 256+nl=20,

6-96 DC2 '*' '1' n User Area Defragment Code 12H 2AH 31H n Definition Range n = 0, 1 Function Defragments the user area (FLA

6-97 DC2 'R' n User Area Initialization Code 12H 52H n Definition Range n=1 Function Initializes user area (FLASH memory). Notes All

6-98 DC2 'w' f [d]k NUL Function Setting Change Code 12H 77H f [d] k 00H Definition Range 0≤d≤255 0≤f≤255 (See the following each

6-99 DC2 'l' n Function Setting Response Code 12H 6CH n Definition Range n=0 Function Reads the MS setting. Notes Responds the presen

6-100 ESC 'c' '4' n Print Stop Capable Paper Sensor Selection Code 1BH 63H 34H n Definition Range 0≤n≤255 Default Depends on

6-101 GS 'r' n Status Data Send Code 1DH 72H n Definition Range 0≤n≤11 Function Sends the specified status data. Printer Status 1 (n=

6-102 Printer Status 3 (n=2) Bit Function Value 0 1 0 FEED Switch status Off On 1 Reserved Fixed to 0 2 Printing Stop Printing 3 Return-wa

6-103 Reserved (n=5 to 7) Bit Function Value 0 1 0 Reserved Fixed to 1 1 Reserved Fixed to 1 2 Reserved Fixed to 1 3 Reserved Fixed to 1 4

6-104 Reserved (n=10 to 11) Bit Function Value 0 1 0 Reserved Fixed to 0 1 Reserved Fixed to 0 2 Reserved Fixed to 0 3 Reserved Fixed to 0

2-5 • When moving the RP-E11 (front paper discharge) model printer from the installation site, lift it upward slowly to leave the rubber feet from t

6-105 GS 'a' n Automatic Status Back Enable/Disable Code 1DH 61H n Definition Range 0≤n≤255 Default When the MS5-1 (Automatic Status R

6-106 (1) The 1st Byte (Printer Status 1) Bit Function Value 0 1 0 Voltage error No Yes 1 Head error Voltage initialization error No Yes 2 Head

6-107 (4) The 4th Byte (Option Sensor Status) Bit Function Value 0 1 0 Reserved Fixed to 0 1 Reserved Fixed to 1 2 Reserved Fixed to 1 3 Draw

6-108 DC2 '0' 'c' n Error History Response Code 12H 30H 63H n Definition Range 0≤n≤255 Function This printer records an erro

6-109 DC2 '>' n Fixed Division Selection Code 12H 3EH n Definition Range 0≤n≤1 Function Sets the thermal head driving method to fix

6-110 (NOTE) When too much energy is applied to the thermal head, it would shorten its life span and cause the paper feed problem. Set an accurate th

6-111 GS 'O' Power Off Execution Code 1DH 4FH Function Turns the printer off. No data is processed after this command is executed. T

6-112 6.5.11 Ruled Line DC3 '#' n Overlapping Mode Selection Code 13H 23H n Definition Range 0≤n≤255 Default Ruled line OR overlapping

6-113 DC3 '-' Ruled Line OFF Code 13H 2DH Default Ruled line OFF Function Sets the ruled line to OFF. Notes After this command is exec

6-114 DC3 'D' nl nh Ruled Line Dot Set Code 13H 44H nl nh Definition Range 0≤nl≤255, 0≤nh≤255 Function Sets 1 to the bit of the [nh ×

2-6 2.1.3 Dimensions 129129等角投影図(S=1/2)単位　：mm外形図129Isometric DrawingUnit: mm USBモデルシリアルモデルUSB+シリアルモデルイーサネットモデル Figure 2-1 RP-E10 Dimensions USB Mo

6-115 DC3 'P' Ruled Line 1 Dot Line Print Code 13H 50H Function Prints a 1 dot line of the selected ruled line buffer image when ruler l

6-116 6.5.12 Download Mode DC2 DC2 Download Mode Selection Code 12H 12H Function Switches to the download mode. Execute hardware reset in order to

6-117 a: Page No. d1: ID data k1: Number of ID data b: Font size d2: Font data k2: Number of font data b Font Size Number of Requiring Dat

6-118 'S' 'R' a b c [d]k 1-byte Font International Character Registration Code 53H 52H a b c [d]k Definition Range a=255

6-119 Font data formatd1d212 dots24 dotsd3 d4d47d48d1d2d168 dots16 dots<24dots font 24×12><16dots font 16×8><1-byte character>02345

6-120 6.5.13 Tag Processing Mode In this mode, input the HTML format tag to create print data. This is not case-sensitive. Since the page mode is used

6-121 (1) Tag processing command GS '{' '0' Tag Processing Start Code 1DH 7BH 30H Function Starts the tag processing mode. Sub

6-122 (2) Tag processing HTML Start Tag <HTML> End Tag </HTML> Function Describes the HTML style tag language. This command reads th

6-123 META Start Tag <META> End Tag None Function Specifies language information. Attribute "charset", "codeset", &qu

6-124 BODY Start Tag <BODY> End Tag </BODY> Function Describes the document's body. Attribute "style" Attribute Val

2-7 等角投影図(S=1/2)単位　：mm外形図129129129Isometric DrawingUnit: mm USBモデルシリアルモデルUSB+シリアルモデルイーサネットモデル Figure 2-2 RP-E11 Dimensions USB Model Serial Model

6-125 P Start Tag <P> End Tag </P> Function Specifies the paragraph. Line feeds are inserted before and after the paragraph. Attribu

6-126 UL Start Tag <UL> End Tag </UL> Function Specifies the list without numbers. Attribute "style" (See the "BODY&

6-127 HR Start Tag <HR> End Tag None Function Prints the horizontal ruled line. Attribute "style" Attribute Value Function st

6-128 TABLE Start Tag <TABLE> End Tag </TABLE> Function Creates the table. Attribute "rules", "cellspacing", &q

6-129 CAPTION Start Tag <CAPTION> End Tag </CAPTION> Function Prints the table's title. It is left aligned in the table. Attrib

6-130 TR Start Tag <TR> End Tag </TR> Function Defines the table's row. Attribute "style" Attribute Value Function

6-131 TH Start Tag <TH> End Tag </TH> Function Defines the table's item as a heading. By default, the element defined as a head

6-132 IMG Start Tag <IMG> End Tag None Function Prints the image registered with the selected key code. Attribute "key-code", &

6-133 BARCODE Start Tag <BARCODE> End Tag </BARCODE> Function Prints the barcode. This command inputs barcode data between the start

6-134 PDF417 Start Tag <PDF417> End Tag </PDF417> Function Prints PDF417. This command inputs barcode data between the start and end

U00127424200 May 2012 U00127424201 July 2012 U00127424202 September 2012 U00127424203 July 2013 Copyright © 2012-2013 by Seiko Instruments Inc. A

2-8 2.1.4 Thermal Paper Specifications Table 2-3 Thermal Paper Specifications Item Specifications Type Normal thermal paper roll Paper width 0 -18

6-135 QR Start Tag <QR> End Tag </QR> Function Prints QR. This command inputs barcode data between the start and end tags. Barcode d

6-136 6.5.14 List of Initial Values (at Initialization) Settings Initial Value Command Character right space amount set 0 ESC SP Bold printing Ca

6-137 Settings Initial Value Command Barcode width 0.375 mm, 0.375/1.000 mm GS 'w' Barcode N:W ratio 1:2.5 DC2 ':' Nominal f

6-138 6.6 COMMAND LIST 6.5.1 Printing Command ...

6-139 6.5.4 Print Position ...

6-140 (1) GS '(' 'L' pL pH '0' fn '0' kc1 kc2 b xL xH yL yH '1' [d]k (2) GS '8' 'L&ap

6-141 FS '-' n Kanji Underline Specify ... 6-79 FS

6-142 DC2 'q' n Execution Response Request ... 6-99 DC2 '

6-143 6.5.13 Tag Processing Mode ...

A-1 APPENDIX A CHARACTER SETS (CHARACTER CODE TABLE) A.1 CHARACTER CODE TABLE (CODEPAGE) Figure A-1 Codepage 437 (USA, Standard Europe)

2-9 2.1.5 Printing Area 1st dot 2nd dotAth dot0.125 mmBC DEPaper FeedDirectionPrinting Surface MS4-5 (Number of Effective Dots Selection): ON Symbol

A-2 Figure A-2 Katakana Character Set Figure A-3 Codepage 850 (Multilingual)

A-3 Figure A-4 Codepage 860 (Portuguese) Figure A-5 Codepage 863 (Canadian-French)

A-4 Figure A-6 Codepage 865 (Nordic) Figure A-7 Codepage 1252 (Latin)

A-5 Figure A-8 Codepage 852 (Eastern Europe) Figure A-9 Codepage 858 (Euro)

A-6 Figure A-10 Codepage 864 (Arabic) Figure A-11 Codepage 1250 (Central European)

A-7 Figure A-12 Codepage 1251 (Cyrillic) Figure A-13 Codepage 1253 (Greek)

A-8 Figure A-14 Codepage 1254 (Turkish)

A-9 A.2 INTERNATIONAL CHARACTER SET The following codes differ depending on the specified international character set. Figure A-15 International C

A-10 A.3 2-BYTE CHARACTER Kanji defined in the JIS 1st and 2nd levels in 1990, NEC selection of IBM extensions, and IBM extensions can be printed. Als

A-11 Figure A-18 NEC Selection of IBM Extension Character Set

2-10 2.1.6 Mark Sensor Specifications (1) Mark Sensor Position BAMarkSensorPrinting Head CPaper Feed DirectionPrinting Surface (NOTE) • The mark s

A-12 Figure A-19 IBM Extension Character Set

Mouser Electronics Authorized Distributor Click to View Pricing, Inventory, Delivery & Lifecycle Information: Seiko Instruments: PW-E242

2-11 (3) How to Use Marked Paper (a) Enable (ON) the MS1-3 (Mark Mode Selection). (b) To change the default settings of the mark position correctio

2-12 2.2 CUTTER SPECIFICATIONS (1) Cutter Specifications Item Specifications Paper cutting method Slide cutting Cutting frequency 1 cut / 2 s max.

2-13 2.3 POWER SUPPLY SPECIFICATIONS (1) Power Supply Connector Specifications Printer side connector: TCS7960-5320177 (HOSIDEN) equivalent Cable sid

2-14 (3) Specified AC Adapter Specifications (PW-E2427-W1) Item Specifications Input voltage AC100 V to AC240 V Input frequency 50 Hz to 60 Hz Out

2-15 2.4 DRAWER KICK PORT SPECIFICATIONS (1) Drawer Kick Port Specifications Item Specifications Output voltage 24 V Output current 1 A max. Numbe

3-1 CHAPTER 3 INTERFACE This chapter describes specifications of each interface required for connecting host devices and peripheral equipment with the

3-2 (3) Connector Printer side connector: UBB-4R-D14T-4D(LF)(SN) (JST) or equivalent (Series B) Figure 3-1 Connector (4) Data reception USB data

PREFACE-1 PREFACE This technical reference describes about RP-E10 SERIES THERMAL PRINTER (hereinafter referred to as "printer"). See USER

3-3 (NOTE) • iSerialNumber is not initially set. • Write an iSerialNumber value that does not duplicate others. • Do not set iSerialNumber three or

3-4 (3) Connector Printer side connector: XM2C-0942-132L (OMRON) or equivalent (D-sub 9P M, fixing screw: #4-40UNC) Figure 3-2 Connector (4) Exa

3-5 MA RKSPA CEMA RKSPA CE(1)(2)(3)(4)DTRRTS Figure 3-4 DTR, RTS Output • When the RTS/CTS control is set (a) RTS outputs MARK signal during ini

3-6 DTRTxDMA RKSPA CE(1)(2)(3)(4)XonXoffXon Figure 3-6 DTR, Xon/Xoff Output (6) Data transmission • When the DTR/DSR control is set Data transmi

3-7 3.3 USB+ SERIAL MODEL The USB+ serial model provides both USB and serial interfaces, and it can be used in the following ways: • The USB interfac

3-8 (2) Pin assignment Pin No. Pin Name I/O Function 1 N.C. - Unconnected terminal 2 TxD O Sends data from the printer to the host device. 3

3-9 (5) Examples of connection with the host device RxD 3TxD 2Host devicePrinterFG 16 DSR5 GND4 DTR3 TxD2 RxD(Shield)9-pin - 9-pinDSR 4GND 5

3-10 • When the RTS/CTS control is set (a) RTS outputs MARK signal during initialization after power on reset. It indicates that the printer is not

3-11 (7) Data transmission • When the DTR/DSR control is set Data transmission is suspended when MARK signal is input in DSR, and TxD sends data whe

3-12 3.4 ETHERNET MODEL 3.4.1 Ethernet Interface (1) General specifications Item Specifications Communication standards 10Base-T / 100Base-TX Comm

PREFACE-2 [Contents] CHAPTER 1 TERMS USED IN THIS MANUAL • This chapter describes the basic terms that are frequently used in this manual. CHAPTER 2

3-13 (4) LED Displays of each LED installed on both sides in the bottom of the connector mean the following: Network Communication System Display L

3-14 Protocol for getting and setting the status: Gets and changes the printer status and network parameters on the special Web page, using t

4-1 CHAPTER 4 FUNCTION SETTING 4.1 FUNCTION SETTING METHOD In this printer, you can preset initial values of items that can be selected after power on

4-2 Changing DIP Switch 4.1.1(1) Change procedures DS is mounted on the interface board of the serial model and USB+ serial model printers. 1. As

4-3 (2) Serial Model Function Setting (DS1) indicates the initial setting. Table 4-1 Serial Model Function Setting (DS1) DS Function Set

4-4 (3) USB+ Serial Model Function Setting (DS1) indicates the initial setting. Table 4-4 USB+ Serial Model Function Setting (DS1) DS F

4-5 Changing Memory Switch 4.1.2(1) Change procedures There are three ways to change the MS. • Using the memory switch setting tool As shown in th

4-6 (2) How to set the Function Setting using the switch operation To set functions using the switch, follow the procedures below. 1. Set a thermal

4-7 6. A message for selecting the setting value of the selected function is printed. Press the FEED switch for the number of times corresponding to

4-8 (3) Function Setting (MS) Details for each setting are described below. The value indicated by the shaded cell (boldface) in the table is set at

TOC-1 TABLE OF CONTENTS CHAPTER 1 TERMS USED IN THIS MANUAL CHAPTER 2 SPECIFICATIONS 2.1 PRINTER SPECIFICATIONS ...

4-9 Table 4-9 Standby LED Selection (MS1-4 to 5) MS1-5 MS1-4 Standby LED Selection 0 0 Aqua 0 1 Green 1 0 Off 1 1 Blue 2. General Sett

4-10 Table 4-12 Buzzer Pattern Selection When an Error Occurs (MS2-3 to 4) MS2-4 MS2-3 Maximum Print Speed Selection 0 0 Pattern1 0 1 Patter

4-11 Table 4-14 Buzzer Count Selection When Cutting Is Complete (MS3-1 to 2) MS3-2 MS3-1 Buzzer Count 0 0 None 0 1 Once 1 0 Thrice 1 1 F

4-12 • Maximum Print Speed Selection (MS4-7 to 8) Selects the maximum print speed at four levels. High: Drives at the maximum speed of 350mm/sec. Mi

4-13 Table 4-18 Maximum Print Speed Selection (MS4-7 to 8) MS4-8 MS4-7 Maximum Print Speed Selection 0 0 Low 0 1 Middle(Quality) 1 0 Middl

4-14 • Cutting Method After Initialization (MS5-8) When the Initial Process After Paper Set is enabled, partial cut or full cut can be selected as th

4-15 6. General Setting 6 (MS6) • Print Density Selection (MS6-1 to 8) Selects the print density to be used. Table 4-21 General Setting 6 (MS6)

4-16 7. General Setting 7 (MS7) • Thermal Paper Selection (MS7-1 to 8) Selects the thermal paper to be used. Table 4-23 General Setting 7 (MS7)

4-17 9. Mark Detection Maximum Feeding Length Setting (MS10 to 11) Sets the mark detection maximum feeding length in 1mm. When the mark cannot be det

4-18 12. Reserved (MS14) MS14 is reserved. To perform 40 bytes all writing, send FFH as a value of MS14. 13. International Character Selection (MS15

TOC-2 CHAPTER 5 LED DISPLAY AND SWITCH FUNCTION 5.1 PRINTER STATUS LED DISPLAY ...

4-19 15. Reserved (MS17 to 39) MS17 to 39 are all reserved. To perform 40 bytes all writing, send FFH as a value of MS17 to 39. 16. Serial Communica

4-20 4.2 TEST PRINT The printer can print the test print. In test print, functions and characters that have been set and the Firmware version are prin

5-1 CHAPTER 5 LED DISPLAY AND SWITCH FUNCTION This chapter describes the printer state by LED display and functions of switches. 5.1 PRINTER STATUS LE

5-2 Table 5-2 LED Flashing Pattern Items Pattern Blink-1 Blink-2 Blink-3 0.2s 0.8s 0.1s 0.7s 0.1s 0.1s 0.1s

5-3 5.2 ERROR AND RECOVERY PROCEDURE When an error except paper-near-end occurs, the printer stops printing operation. However, the data reception is

5-4 5.3 SWITCH There are two switches, POWER Switch and FEED Switch in this printer. 5.3.1 POWER Switch Turning ON/OFF the printer can be performed b

6-1 CHAPTER 6 COMMAND FUNCTIONS 6.1 CHARACTER CODES AND COMMANDS The character code range and user-defined character codes vary when kanji mode is sel

6-2 (2) Character code of 2-byte code system character 2-byte character is specified with 2 bytes character code. (a) 1st byte 00H: 1-byte code sys

6-3 6.1.2 Shift JIS Code System When Shift JIS code system is selected with "Kanji Code System Selection" command (FS 'C'), kanji

6-4 6.2 FLASH MEMORY A FLASH memory on this printer allows for using user-defined characters, downloaded characters, optional fonts, macro function, N

TOC-3 FIGURES Figure 1-1 Relationship between Input Buffer and Line Buffer ... 1-1 Figure 1-2 Line S

6-5 Table 6-1 Memory Area After Initialization Use Bytes User-defined characters 9784 Downloaded characters 6184 Optional font 0 Macro 0 NV g

6-6 (2) Memory control information After allocating the area, the memory control information is added at the beginning of the allocated area. The num

6-7 (3) Precautions for the macro function Macro function cannot include the commands for allocating or freeing (up) the memory area listed in Table

6-8 (4) Memory management 1. About memory in the user area of FLASH memory Memory in the user area of FLASH memory has the following three kinds of

6-9 2. Precaution of the FLASH memory area rewriting, release and ensure When defining and registering the command (user-defined character, download

6-10 6.3 STANDARD MODE AND PAGE MODE There are two ways for print mode: the standard mode that this printer prints the received data each time or the

6-11 Table 6-5 When Multiple Prints Are Desired Procedure Command Description Remark 1 ESC 'L' Selects the page mode. The standard

6-12 • Barcode The reference point of the barcode is lower left. The next mapping start position shifts horizontally for the barcode width. • Raster

6-13 5. Buffer full processing When the character data exceeds a line buffer, the subsequent data is mapped from the beginning of the next line. When

6-14 6.4 RESPONSE DATA All of upper 4 bits in response data to the host device are identifiers. Table 6-7 shows the meanings to the identifiers. Table

TOC-4 TABLES Table 2-1 Printer Specifications ... 2-1 Ta

6-15 (5) Progress situation response Sends various progress situation by lower 4 bits at 16 steps. (6) Initialized response Sends 1 byte code after

6-16 6.5 FUNCTION CODE DESCRIPTION This chapter describes the commands in each function. ×× ×××× Command The name of th

6-17 6.5.1 Printing Command LF Line Feed Code 0AH Function [When the standard mode is selected] Prints the data in the line buffer and performs li

6-18 CR Carriage Return Code 0DH Function This command is ignored. ESC FF Page Mode Data Print Code 1BH 0CH Function In the page mode, batch pr

6-19 ESC 'j' n Print and Feed Backward Code 1BH 6AH n Definition Range 0≤n≤255 Function Feeds the thermal paper backward for a predefi

6-20 CAN Print Data Cancel in Page Mode Code 18H Function Deletes all the data in the latest print area in the page mode. Notes Only valid when t

6-21 6.5.2 Line Spacing ESC '2' 1/6 Inch Line Spacing Set Code 1BH 32H Function Specifies the line spacing per line as 1/6 inch (34 dots

6-22 6.5.3 Character Set ESC SP n Character Right Space Amount Set Code 1BH 20H n Definition Range 0≤n≤255 Default n=0 Function Sets the amount

6-23 ESC '!' n Print Mode Select Code 1BH 21H n Definition Range 0≤n≤255 Default n=0 Function Selects the print mode. Bit Function

6-24 ESC 'M' n Character Font Select Code 1BH 4DH n Definition Range n=0, 1, 48, 49 Default n=0 Function Selects a character font. n

TOC-5 Table 6-3 Commands for Allocating or Freeing Memory Area ... 6-7 Table 6-4 When Only One Print

6-25 Notes The setting applies to all characters (including kanji) except HRI characters. However, as for the character size of optional font, the sc

6-26 Function Specifies or cancels bold printing. When n=<*******0>B, cancels bold printing. When n=<*******1>B, specifies bold printing.

6-27 ESC '{' n Inversion (Flip) Printing Specify/Cancel Code 1BH 7BH n Definition Range 0≤n≤255 Default n=0 Function Specifies or can

6-28 This command does not affect the space between lines. Bold printing specified and double strike printing are ignored. (Line width of reverse pr

6-29 ESC 't' n Character Code Table Select Code 1BH 74H n Definition Range n=0 to 5, 16, 18, 19, 37, 45 to 48, 255 Default Depends on

6-30 a Font Size 0 24 dots font 1 16 dots font c Function Response Type 0 Reserved - 1 Reserved - 2 Reserved - 3 Check SUM (2 bytes) HE

6-31 ESC '&' y s e [x [d]k]n Downloaded Character Registration Code 1BH 26H y s e [x [d]k]n Definition Range y=3 (when font A (24×1

6-32 24 dots12 dotsMSBLSBd1d2d4d5d34d35d3d6d3665432107d1d2d3d4d15d16654321016 dots8 dotsMSBLSB7 ESC '%' n Downloaded Character Set Specify

6-33 DC2 'D' n Downloaded Character Area Operation Code 12H 44H n Definition Range 0≤n≤255 Function Releases or allocates the download

6-34 DC2 'P' s e y x [d]k Optional Font Registration Code 12H 50H s e y x [d]k Definition Range 20H≤s≤e≤7EH 1≤y≤127, 1≤x≤127 Fu